Search Results

A driving simulator system for developing steering road feel has been developed. A new steering gear box or an electronic steering system is installed on the simulator and its road feel and control algorithm are developed according to the characteristics of any vehicle which has been programed into the engineering work-station. The vehicle model programed into the engineering work station runs according to the driver's operations, which are fed through the new steering system to be tested. The steer-restoring torque of the vehicle programed into the engineering work-station is produced by an actuator, and gives the impression through the new system of having been fed back from an actual road.

Diesel particulate trap systems are one of the effective means for the control of particulate emission from diesel vehicles. Hino has been researching and developing various diesel particulate trap systems for city buses. This paper describes two of the systems. One uses a wall flow filter equipped with an electric heater and a sensing device for particulate loading for the purpose of filter regeneration. Another makes use of a special filter named “Cross Flow Filter” with an epoch-making regeneration method called “Reverse Jet Cleaning”, by which it becomes possible to separate the part for particulate burning from the filter. Both systems roughly have come to satisfy the functions of trap systems for city buses, but their durability and reliability for city buses are not yet sufficient.

Thai Hino Industries, one of Hino Motors Ltd.'s major overseas joint ventures, has been manufacturing trucks since it was founded over 20 years ago. During that time, Hino Motors, in cooperation with the Government of Thailand, has increasingly localized the production of vehicle component parts. Today, calculated by item, 45% of all such parts are produced by Thai Hino Industries and its local suppliers. As a result, Thai Hino Industries has grown into a company which makes significant contributions not only to the automotive industry but to Thailand's industrial sector as a whole. Localization of Thai Hino progressed from the transfer of vehicle assembly know-how, to the establishment of feasible guidelines for parts production localization, then on to the transfer of production engineering know-how for flexible manufacturing systems, and finally to the transfer of production engineering know-how for press dies.

The spark-assisted methanol engine has disadvantages like poor fuel economy especially at light load and low spark plug durability affected by combustion characteristics. Investigations of combustion characteristics of the spark ignition system and the autoignition system in the methanol engine and discharge characteristics of a spark plug are described in this paper. It is clear that effective autoignition was accomplished by increasing the compression ratio and adopting an EGR system in the spark-assisted methanol engine. This new improved methanol engine which is named HAMS achieved good fuel economy at light load, a low NOx emission and longer spark plug life. And a heat insulated piston with a stainless steel cap is being investigated for further improvement of autoignition combustion characteristics.

Noise reduction of diesel engines installed in heavy duty vehicles is one of the highest priorities from the viewpoints of meeting the regulations for urban traffic noise abatement and noise reduction in the cabin for lightening fatigue with comfortable long driving. It is necessary that noise reduction measures then be applied to those causes. Noise reduction measures for the diesel engine can be classified into five categories on the noise radiation block-diagram. These are, reduction of combustion and mechanical forces, deformation and vibration control of cylinder block, vibration control of fastened components, prevention of standing wave and close fitting shields. All noise reduction measures for the diesel engine researched for the purpose of practical use are fully described in this paper.

Gaseous emission measurements of a diesel engine including hydrocarbons (HC), carbon monoxide (CO), and oxide of nitrogen (NOx) are made in accordance with the procedures specified in the Federal Register. However, it is very difficult to maintain constantly the accuracy of these emission measurements due to failure of the emission analyzer. The authors have thus developed the Pre-Alarm Diagnostic System for a Diesel Emission Analyzer. Firstly, the authors have carried out analysis of all failure modes that are classified into initial failure, random failure and wearing-out failure, plus tolerance level for prediction of failures and method of predicting failures. Next, the authors have developed the Pre-Alarm Diagnostic System that is able to easily discover these failures before the exhaust emission test. In this system, 40 sensors, such as pressure, temperature, voltage etc, are laid in each pipe line of connection between exhaust emission sampling pump and analyzer.

Recently the analysis of air-fuel mixing and combustion has become important under the stringent emissions regulations of diesel engines. In the case of gasoline engines, the KIVA computer program has been developed and used for the analysis of combustion. In this paper, the calculations of combustion phenomena in DI diesel engines are performed by modifying the KIVA program so as to be applicable to multi-hole nozzles and arbitrary patterns of injection rate. The thermophysical and ther-mochemical properties of gasoline are altered to those diesel fuel. In order to investigate the ability of this modified program, the calculations are compared with the experiments on single cylinder engines concerning the pressure, flame temperature and mass change of chemical species in cylinders. Furthermore, the calculation for the heavy duty DI diesel engine is performed with this diesel combustion program.

For the 1990's diesel engines, particulate control has been an important problem. The purpose of this paper is to discuss emission control needs for heavy duty diesel truck engines for the 1990's. This paper will focus on the factors such as fuel injection pressure and fuel properties which most affect particulate emission. The characteristics of diesel spray in the atmosphere and also actual combustion of a turbocharged and charge-cooled H.D. D.I diesel engine were studied as a function of injection pressure ranging from 50 to 150 MPa. Experimental results show that high pressure injection improves the atomization and air entrainment. Though Bosch smoke level, fuel consumption and combustion period decreased with the rise of injection pressure, particulate emission in EPA transient test cycle did not decrease dut to an increase of SOF.

Characteristics of diesel combustion with high pressure fuel injection were investigated, using a supercharged and charge air cooled single cylinder engine. Observation and analysis of combustion was performed using high speed schlieren photography at a definite low level NOx emission, while varying the parameters of both injection pressure and swirl ratio. Engine performance at a high injection pressure was evaluated in combination with shallow dish type combustion chamber and 8 hole nozzle. Two different intake ports (higher and lower swirl ratio) were used for the evaluation. Conventional injection system in combination with toroidal cavity and 4 hole nozzle was compared as a base line. It is generally said that quiescent combustion system is suitable for higher injection pressure configuration. According to the observed result of combustion photographs, however, higher swirl ratio shows better mixing than a lower swirl ratio, which was also confirmed by the performance test.

In order to reduce particulate and NOx emission from the direct injection diesel engine, most researchers have been expecting the utilization of higher injection pressure and injection rate for improvement of diesel combustion. In the case of pump-line-nozzle system, the injection pipe line is very important with regard to the high injection pressure. Namely, the pipe line must be able to resist not only high pressure but also cavitation erosion. In this paper, the effect of high injection pressure, injection rate and sharp cutting at the end of fuel injection are discussed along with cavitation phenomena on the injection pipe line. And durability tests on the pipe line system under high injection pressure using a test rig are also described. Regarding durability tests, several measures have been taken for the injection pipe. As a result, the authors have found that the best solution for the injection pipe is a composite pipe made with SUS and steel.

Experiments on a large number of soluble fuel additives were systematically conducted for diesel soot reduction. It was found that Ca and Ba were the most effective soot suppressors. The main determinants of soot reduction were: the metal mol-content of the fuel, the excess air factor, and the gas turbulence in the combustion chamber. The soot reduction ratio was expressed by an exponential function of the metal mol-content in the fuel, depending on the metal but independent of the metal compound. A rise in excess air factor or gas turbulence increased the value of a coefficient in the function, resulting in larger reductions in soot with the fuel additives. High-speed soot sampling from the cylinder showed that with the metal additive, the soot concentration in the combustion chamber was substantially reduced during the whole period of combustion. It is thought that the additive acts as a catalyst not only to improve soot oxidation but also to suppress soot formation.

A current unmodified and modified engines with different amounts of thermal insulation have been used to generate data from which changes in bsfc, cooling loss, emissions, exhaust loss were determined. Since legislative requirement exists for allowable emission of NOx, fuel injection timing and other controllable factors were adjusted to maintain constant NOx emission except a test of influence on NOx emission according to the rate of heat insulation (adiabaticity). The effect of higher combustion temperature on the combustion phenomena is discussed.

The purpose of the investigation presented here was to develop a high quality SAE 10W-30 engine lubricating oil to meet the heavy duty operating conditions of trucks. The operation of their engines is predicted to become more severe in future because of the trend toward higher power output, nore severe regulation of exhaust emissions and noise as well as the increasing demand for better fuel economy. To meet these demands, an improvement of the wear resistance of engine lubricating oil was considered to be the most important aspect for the development of high performance diesel engines in the future. The engine test developed was able to evaluate various experimental oils by observing wear resistance of the valve train which is considered to be one of the most severe tri-bological conditions. The best oils were determined by optimum selection of the amount and type of detergent, ashless dispersant and zinc dithiophosphate.

A new combustion system for a light duty D. I. diesel engine was developed and introduced (1)*. The combustion chamber, which was used in the combustion system, has 4 concaves on the periphery of the inner wall and was calld HMMS-III. This combustion chamber realized better fuel consumption and lower smoke level over a wide speed range. However, the effects of HMMS-III combustion chamber on in-cylinder air motion and combustion characteristics were not yet clarified in the previous paper. In this study, in order to clarify the effects of HMMS-III combustion chamber on in-cylinder air motion and characteristics, analysis of flow direction and streak line via oil film method was carried out in comparison with flat dish and re-entrant type combustion chambers. Further, measurement of in-cylinder air motion by L.D.V. and observation of mixture formation and burning process via high speed schlieren photography were carried out.

Fuel injection timing retardation for reducing exhaust emission of direct injection diesel engines prolongs the period to complete cold starting. Engine speed at this period varies through some accelerating and faltering stages. The speed variation and relating combustion characteristics was investigated through the measurement of cylinder pressure for each cylinder as well as the dynamic fuel injection timing and instantaneous engine speed. An improvement of cold start was shown by application of afterheat of a sheathed type glow plug and an electronic fuel injection timing control device.

A new combustion system for a light duty D.I. diesel engine was developed, and a 3.5 ton payload truck (6.5 ton G.V.W.) equipped with this D.I. diesel engine and this combustion system realized good fuel economy and lower exhaust gas emission. Generally, light duty vehicles have to operate over a wide engine speed range. Therefore application of a D.I. diesel engine to light duty vehicles is difficult because of combustion tuning requirements over a wide engine speed range. Up to now, most of the diesel engines for light vehicles have been of the I.D.I. type. But the D.I. diesel engine has an evident advantage of lower fuel consumption. In these circumstances the authors developed a new combustion chamber shape for a small D.I. diesel engine with turbulence induced intake port and optimum fuel injection equipment. Various combustion chamber geometries were tested and evaluated.

In a diesel engine, the mixing of the fuel spray and in-cylinder air controls rate of beat release during combustion, namely it will determine the thermal efficiency, maximum output and gas or noise emission, etc. Therefore, it is important to measure the droplet size and its volume density distribution in diesel fuel sprays. The optical measuring method, which includes a light scattering and holographic technique, seems the only feasible method for analysing these unsteady characteristics of fuel sprays. The light scattering technique described herein was based upon Mie scattering theory, and the droplet size and volume density distribution of fuel sprays were calculated from the combination of the light extinction and the forward-to-backscattering ratio of Mie scattering intensity. The volume density and droplet size distribution of fuel sprays were obtained from the light intensity distribution on a photograph of fuel sprays.